Cobra Electronics Marine Radio MARINE User Manual

0

Out of 0 Ratings

Owner's of the Cobra Electronics Marine Radio MARINE gave it a score of 0 out of 5. Here's how the scores stacked up:

  • Reliability

    0 out of 5

  • Durability

    0 out of 5

  • Maintenance

    0 out of 5

  • Performance

    0 out of 5

  • Ease of Use

    0 out of 5
of 42
 
Nothing Comes Close to a Cobra
®
Digital Select Calling (DSC)
Setup
41
40
English
Digital Select Calling (DSC)
Setup
DSC Set-Up
•
Digital selective calling — DSC — employs digital RF signals which tend to carry
further and be less susceptible to distortion from noise and atmospheric conditions
than analog ones. The result is greater range and more reliable message delivery
per watt of output power.
But, that is not the only advantage of DSC equipped radios. Those radios are set up
to interface with GPS and to automate many of the operations involved in sending
and receiving messages. That results in more compact and accurate messages and
less congestion of the airwaves.
The price of these benefits to the user is the time it takes to do the required set-up
to make the DSC features work. A little time spent when your radio is new will pay
dividends over its life.
These procedures use the Settings menu. Refer to page 38 for information on
entering and exiting the Settings menu.
User MMSI Number
The nine (9) digit MMSI number, similar to a telephone number, is a unique identifier
for a vessel. DSC incorporates this number into every message that is Sent (Tx) or
Received (Rx). Enter the MMSI number as soon as you receive your MMSI number
from the issuing agency listed on page 9.
NOTE
The radio does not operate in the DSC mode until an official MMSI number is
entered. An error tone will sound when attempting to operate in the DSC
mode without an MMSI number.
NOTE
An MMSI number can only be entered one time. To create a new MMSI
number, the unit must be reset by the dealer.
To Enter Your MMSI Number:
1. Enter the Settings menu and scroll to
USERMMSI
with the Up/Down buttons.
2. Press the Call/Set button and the blinking cursor will
appear at the first digit under
USER MMSI ID ENTRY.
3. Use the Up/Down buttons to scroll through the number
list to that digit of your number.
4. Press the Call/Set button to select the digit and the
blinking cursor will move to the next digit of the number.
5. Repeat steps 3 and 4 until all nine (9) digits of your
MMSI number are entered.
NOTE
Press the High/Low Power button to backspace
and erase the last selected number.
6. Check that you have entered the number correctly. The
unit will ask you to re-enter your number to confirm.
7. Press and hold the Call/Set button to return to the
Settings menu.
If You Incorrectly Enter Your MMSI Number
You can repeat steps 1 through 7 to correct it. HOWEVER,
YOU CAN DO THIS ONLY ONCE! A third attempt to enter
an MMSI number will result in an error message as shown.
Pressing the Call/Set button from the error message
will return the radio to the Settings menu.
Once the error message appears, the radio will still
operate in all non-DSC modes. But you will have to
return the radio to Cobra
®
Electronics (see product
service on page 73 for details) for reset before you
can enter your MMSI number and use the radio in
DSC mode.
Because the MMSI number is so important to DSC
operation, this limitation is imposed on all DSC capable
radios to prevent constant changes and the potential
introduction of errors in the process. If, for any reason,
it is necessary to change the MMSI number in the radio
more than once, you can return it to Cobra
®
Electronics
for reset.
Operating Your Radio Operating Your Radio
User MMSI ID Entry
Error Message
Call/Set Button
User MMSI
F75D_OPERATION:F75-Operation-8 12/13/10 3:52 PM Page 40

   Find Your Products By Category