iBatteryCase - iPhone 3G & 3Gs Battery Case
PLEASE READ THIS INFORMATION THOROUGHLY BEFORE USING THIS PRODUCT. IT CONTAINS IMPORTANT
OPERATING INSTRUCTIONS FOR YOUR POWERPORT UNIT.
Thank you for purchasing the iBatteryCase - iPhone 3G & 3Gs Battery Case. The iBatteryCase case oers the
convenience of an external battery built into the full protection of a hard case. You can use it as a case all
the time never having to remove it and enjoy the convenience of extra battery power when you need it.
Included in the package you have purchased:
iBatteryCase, USB charging / Sync cable and User Manual
Note: Prior to initial use fully charge your iBatteryCase before connecting to your iPhone.
You can charge the iBatteryCase case with the Micro USB to USB cable included with the case.
Just plug the Micro USB into the case, and the other ends USB into a computer USB port or into
a wall plug style adapter that has a USB out. Switch the iBatteryCase to “OFF” and the case will
begin to charge.
The LED status indicators show the charging status of the case. The rst LED will blink as it’s charging then
become steady, and then the second will blink and also become steady. Finally the third will blink and once the
case is fully charged it will also become steady. Then the charging progress is done.
Charging your iPhone while installed in the iBatteryCase.
When charging an iPhone while installed in the iBatteryCase, switch the” ON / OFF” button located
on the bottom of the case to “ON” to allow the iPhone to charge. To charge just the iBatteryCase switch
to “OFF” and the case will charge.
With the built in ON / OFF switch you have the option of using the
iBatteryCase when you need it. When you need an extra charge in
your phone just switch it to the “ON” position and the iPhone case
will proceed to charge your main battery. If you are not quite ready
to charge you phone just leave the switch in the”OFF” position.
Slide your iPhone facing you into the iBatteryCase from the top
making sure the 30 pin connector and the bottom of the iPhone
line up and connect correctly. Then take the top cover aligning it
into the channels of the lower case, slide down until it sets rmly
into the bottom half of the case. (Pay attention to the openings for
the headphone jack and the power jack, making sure they line up.)
Once connected you can turn the switch located on the bottom of
the case to the “ON” position. You should now see the charge
indicator icon appear on your iPhone.
With the “ON / OFF” switch in the “ON” position your iPhone will always drain the case rst until its power is 5%,
then your iPhone switches to its main battery. With the “ON / OFF” switch in the “OFF” position your iBatteryCase
is in standby mode ready to charge your iPhone by switching it to the “ON” position.
The integrated LED status indicator tells you exactly how much battery power is
left in your case. Simply press the test button The 1st LED will indicate 30% or
less charge remaining, the 2nd LED will indicate between 30 – 70% charge
remaining and the 3rd LED will indicate 70 -100% of charge remaining.
Limited 1 Year Warranty
This limited warranty starts from the date of original purchase and expires one year thereafter. If, during this period, any part, because of manufacturing defects or
workmanship, fails to function properly under normal use it will be repaired at no charge for parts and labor or, at our option, the product will be replaced. The following
is excluded: damages from delay or loss of use of equipment or damaged batteries, malfunctions resulting from misuse, tampering, unauthorized repairs, modications
Package the unit and its accessories carefully using ample padding material to prevent damage in transit and ship it prepaid and insured to:
LENMAR ENTERPRISES, INC.
4035 Via Pescador
Camarillo, CA 93012 USA
When sending in product for service, your package should include evidence of date and place of purchase. Enclose $10.00 for shipping and handling for addresses in
the U.S. and $15.00 in Canada. For outside the U.S. and Canada, freight will vary depending upon ship-to address.
Proposition 65 Notice (California)
The following statement is required in the state of California pursuant to the settlement of an action brought by the Mateel Environmental Justice Foundation against
multiple electronics and appliance manufacturers
• WARNING: Handling the cord on this product will expose you to lead, a chemical known to the state of California to cause birth defects or
other reproductive harm. Wash hands after handling.
For additional questions, comments or to explore other Lenmar battery solutions, visit our web site at: www.poweredbylenmar.com or
call 800/424-2703 from 9AM – 5PM PST.
Charging Your iBatteryCase
Installing your iPhone into the iBatteryCase
Checking remaining capacity of the case
Enjoy the convenience of syncing your iPhone without ever removing the case.
Using the supplied cable you can charge and sync your iPhone to iTunes without
ever removing it. Just plug the supplied Micro USB cable in to the case and the
other end into your computers USB slot.
The LED light is activated by pressing and holding down the button next to the
LED status indicators until it lights. To turn it o press and hold the button again
until it turns o.
The camera function on your iPhone works with no obstructions while the case is on, in fact the LED Light will add
to the light on your indoor pictures. Just hold the button next to your LED status indicators until it lights, when
your nished taking pictures just hold the button again until the LED Light shuts o.
Operating the camera
Up to 240 hours*
Up to 4hours*
Up to 4.5 hours and on Wi-Fi up to 5 hours*
Up to 17 hours*
Up to 5 hours*
*All above times can vary due to device settings, location, and signal strength.
Lithium-Polymer battery must be
recycled or dispose of properly.
Micro USB port
Apple 30 Pin Connector