2.5

Out of 3 Ratings

Owner's of the Conair Electric Shaver Conair Electric Shaver gave it a score of 2.5 out of 5. Here's how the scores stacked up:
  • Reliability

    2.0 out of 5
  • Durability

    2.0 out of 5
  • Maintenance

    2.0 out of 5
  • Performance

    3.0 out of 5
  • Ease of Use

    3.33 out of 5
of 2
 
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, especially
when children are present, basic safety pre-
cautions should always be taken, including the
following:
READ ALL INSTRUCTIONS
BEFORE USING
Keep away from water
DANGER– Any appliance is electrically
live, even when the switch is off.
To reduce the risk of death or injury by
electric shock:
1. Always unplug appliance from electrical
outlet immediately after using.
2. Do not place or store appliance where it
could fall or be pulled into a tub or sink.
3. Do not use appliance while bathing or in the
shower.
4. Do not place appliance in, or drop into,
water or other liquids.
5. If appliance has fallen into water, do not
reach for it. Unplug immediately.
DO NOT REACH
INTO THE WATER
WARNING – To reduce the risk of burns,
electric shock, fire, or injury to persons:
1. Never leave a plugged-in appliance
unattended.
2. This appliance should not be used by, on,
or near children or individuals with certain
disabilities.
3. Use appliance only for its intended use
as described in this manual. Only use attach-
ments recommended by the manufacturer.
Do not use an extension cord to operate the
appliance.
4. Never operate the appliance if it has
a damaged cord or plug, is not working
properly, has been dropped or damaged, or
dropped into water. Return the appliance
to a Conair service center for examination
and repair.
5. Keep the appliance cord away from heated
surfaces.
6. Do not pull, twist or wrap the cord around
the appliance.
7. Never drop or insert any object into any
opening of the appliance.
8. Do not place the appliance on any surface
while it is operating.
9. Never operate the appliance with the air
openings blocked or place appliance on a soft
surface, such as a bed or couch, where the
air openings may be blocked. Keep the air
openings free of lint, hair, an the like.
10. Do not use the appliance with a damaged
or broken comb or with teeth missing from
the blades, as injury may result. Before each
use, make certain the blades are aligned
properly and oiled.
11. Do not use the appliance outdoors or
where aerosol (spray) products are being used
or oxygen is being administered.
SAVE THESE
INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
OPERATING INSTRUCTIONS
1. Remove the battery compartment cover by
pushing in and down toward the bottom of the
trimmer.
2. Align the two AA batteries with the positive
and negative positions indicated inside the bat-
tery compartment. Being careful not to bend the
clips, insert the negative end of each battery first
so it will slip easily into position.
3. Return the battery cover to its original position
by pushing it in and up until you hear a small
click as it locks into place.
4. To use your trimmer, push ON/OFF switch
upwards to ON position.
5. After you finish using your trimmer, push
down on the ON/OFF switch to turn the trimmer
off.
6. For your convenience, the trimmer comes
with a storage base to hold the trimmer and
accessories.
7. Always purchase the correct size and grade
of battery most suitable for the intended use.
8. Replace all batteries of a set at the same
time.
9. Clean the battery contacts and also those of
the devise prior to battery installation.
10. Ensure the batteries are installed correctly
with regard to polarity (+ and -).
11. Remove batteries from equipment, which is
not to be used for an extended period of time.
12. Remove used batteries promptly.
13. Do not mix old and new batteries.
14. Do not mix alkaline, standard (Carbon-
Zinc), or rechargeable (Nickel cadmium or
Nickel Metal Hydride) batteries.
USER MAINTENANCE
INSTRUCTIONS
TAKING CARE OF YOUR TRIMMER
OILING THE BLADES
About once a month you should oil the trim-
mer blades with the oil provided in your kit. It
is best to do this over a piece of newspaper.
Turn the trimmer on and hold it so that the
blades are pointed downward. Spread one
drop of oil across the blades, then turn the
trimmer off and wipe away the excess oil with
a soft cloth.
Be careful not to use too much oil and don’t
oil your trimmer more than necessary, as this
could damage the motor. (Never attempt to
oil the motor bearing, as it is permanently
lubricated.) After oiling the blades, return the
trimmer and oil packet to the trimmer storage
base. KEEP OIL OUT OF REACH OF CHILDREN.
ON/OFF SWITCH
To operate, simply push slide toward blade; to
stop, push slide away from blade.
*Requires 2 AA batteries (not included). We recommend
using alkaline batteries in your trimmer because they
last longer.
BLADE CARE
Because the trimmer blades are precision-
made for a very special use, they should
always be handled with care. Each time you
finish using the trimmer, take the cleaning
brush provided and brush away any loose hair
that has collected in the blades. Then store
the trimmer in its storage base to protect the
blades until the next use.
Be especially careful when changing or adjust-
ing blades. When you have your trimmer ser-
viced, be sure that both blades are sharpened
or replaced at the same time.
To promote the long life of the appliance, use
your trimmer only for the purpose intended
by the manufacturer – to trim your beard and
mustache.
REMOVING BLADE SET
This trimmer comes with a detachable
blade set; which makes maintenance and
replacement easy.
To remove the blade set:
• Make sure the trimmer is in the off position
• With the power switch facing you, press the
blade on the teeth and in direction away from
you until they pop out of the housing
TO REPLACE THE BLADE SET
• Looking at the trimmer from above you will
see a notch at the back of the trimmer.
• There is a tab on the blade set on the bottom,
opposite the blades
Position that tab so that it fits into the notch
inside the trimmer head
Push the blade set down onto the trimmer
head until it snaps into place.
GROWING A BEARD AND MUSTACHE
There are three key factors that will determine
which beard or mustache style is best for you:
1. The shape and dimensions of your face.
2. The natural growth of your beard/mustache.
3. The thickness of your beard/mustache. If
you are unsure about the type of beard or
mustache that would most suit your face,
speak with a professional hair stylist and ask
for an opinion on what style would be best.
Once your beard or mustache has been styled,
it is essential that you maintain its appear-
ance. To do this, use your trimmer to trim your
beard/mustache weekly.
For the best trimming results, your beard
should be slightly damp (NOT WET) when
using your trimmer. This will prevent the trim-
mer from removing more hair than desired.
TYPES OF BEARDS/MUSTACHES
GETTING STARTED:
OUTLINING YOUR BEARD
1. It is always best to begin
with a clean, slightly damp
beard.
2. After you have combed
through your beard in the
direction it grows naturally, you will want to
outline the desired shape, beginning under
your jawline.
3. Begin defining your beard’s shape under
your chin and work upward on each side
of your face toward your ears. Then define
the upper outline of your beard across your
cheeks, past your sideburns, and toward your
hairline.
Battery Position
On/Off Switch
NOW YOU’RE READY TO TRIM
YOUR BEARD
1. Your trimmer adjusts to five positions so you
can have a beard length from 1/8" (shortest)
to 5/8" (longest).
2. To use the 5-position comb, slide the unit
over the trimmer blades and snap it down into
position. At first, until you become familiar with
the adjustments, use the longest trim setting
(5/8"). (You can always go back and make
your beard a little shorter.)
3. Begin trimming your
beard using smooth,
even strokes. Start with
your sideburns and work
downward toward your
chin. (Never attempt to trim against the natural
growth of your beard because the hair will be
cut too short.)
4. If you decide you want a closer trim, you
can now adjust the 5-position comb attach-
ment to a shorter setting (such as 1/2" or
3/8") and go over your beard again until you
achieve the desired length.
BLENDING THE JAWLINE
1. The three jawline attachments will help you to
achieve a neat, finished trim under your chin. To
use one of the attachments, press it down over
the trimmer blades until it clicks into position.
2. Hold the trimmer in an upright position and
begin trimming under your jawline, using short,
even strokes.
3. After your beard is blended, turn off the trim-
mer and remove the attachment by gently pull-
ing up on tab.
TO TRIM YOUR MUSTACHE
1. For best results, start with a clean, slightly
damp mustache.
2. Comb through your
mustache in the direction
it grows.
3. Place the 5-position comb over the trimmer
blades and snap it into position. It is a good idea
to start with the longest trim setting adjustment.
(You can always go back and cut your mustache
more closely with a shorter setting.)
ALWAYS TRIM YOUR MUSTACHE
FROM THE TOP DOWN
4. After your mustache
has been trimmed to the
desired length, remove
the 5-position comb and,
using the blades only,
define the outline of the bottom of
your mustache.
MEDIDAS DE
SEGURIDAD
IMPORTANTES
Siempre que use aparatos eléctricos, especial-
mente en la presencia de niños, debe tomar
precauciones básicas de seguridad, entre las
cuales las siguientes:
LEA TODAS LAS
INSTRUCCIONES
ANTES DE USARLO
maNtÉNGaLo aLeJaDo
DeL aGUa
PELIGRO– Cualquier aparato enchufado
permanece bajo tensión, aunque esté apagado.
Para reducir el riesgo de muerte o herida por
descarga:
1. Siempre desconecte el aparato inmedi-
atamente después de usarlo.
2. No coloque ni guarde el aparato donde pueda
caer o ser empujado a una bañera o un lavabo.
3. No lo use en el baño o la ducha.
4. No coloque el aparato ni lo deje caer al
agua u otro líquido.
5. No trate de alcanzar el aparato después
de que hubiese caído al agua. Desconéctelo
inmediatamente.
NO TRATE DE
ALCANZAR LA
UNIDAD EN EL AGUA
ADVERTENCIA – Para reducir el
riesgo de quemaduras, electrocución, incendio
o heridas:
1. Nunca deje el aparato desatendido mien-
tras esté conectado.
2. Este aparato no debería ser usado por,
sobre o cerca de niños o personas con alguna
discapacidad.
3. Utilice este aparato únicamente con el
propósito para el cual fue diseñado y sola-
mente según las instrucciones. Sólo use
accesorios recomendados por el fabricante.
No utilice una extensión con este aparato.
4. No opere este aparato si el cordón o la
clavija estuviesen dañados, después de
que hubiese funcionado mal o que se hub-
iese caído o si estuviese dañado. Regrese
el aparato a un centro de servicio autor-
izado para su revisión y reparación.
5. Mantenga el cable alejado de superficies
calientes.
6. No jale, retuerza ni enrolle el cable alred-
edor del aparato.
7. Nunca deje caer ni inserte ningún objeto
las aberturas del aparato.
8. No coloque el aparato en ninguna superficie
mientras esté funcionando.
9. Nunca bloquee las aberturas de aire ni
coloque el aparato en una superficie blanda,
como una cama o un sofá, donde se puedan
obstruir. Mantenga las aberturas libres de
pelusas, cabellos y elementos similares.
10. No utilice este aparato con guías o cuchil-
las rotas o dañadas. Esto podría provocar una
herida. Asegúrese de que las cuchillas estén
debidamente alineadas y lubricadas antes de
cada uso.
11. No lo utilice en exteriores, ni lo haga fun-
cionar donde se estén usando productos en
aerosol (spray) o donde se esté administrando
oxígeno.
GUARDE ESTAS
INSTRUCCIONES
PARA USO DOMÉSTICO SOLAMENTE
INSTRUCCIONES DE OPERACIÓN
1. Deslice la cubierta del compartimiento de la(s)
pila(s) hacia abajo para abrirlo.
2. Instale dos pilas AA, respetando los signos de
polaridad. Introduzca el polo negativo primero,
teniendo cuidado de no doblar las patas de
contacto.
3. Cierre la cubierta del compartimiento de la(s)
pila(s), empujando hasta que haga clic.
4. Para encender el aparato, deslice el interrup-
tor hacia arriba (ON).
5. Para apagar el aparato, deslice el interruptor
hacia abajo (OFF).
6. Para su comodidad, este aparato incluye una
base de almacenaje para la cortadora y sus
accesorios.
7. No utilice pilas que no sean del tamaño o de
la potencia indicada para uso con este aparato.
8. Cambie todas las pilas al mismo tiempo.
9. Limpie los contactos del aparato y los de las
pilas antes de instalar éstas.
10. Siempre respete los signos de polaridad al
instalar las pilas (+/-).
11. Retire las pilas si no va a usar el aparato
durante un largo período de tiempo.
12. Retire las pilas usadas sin demora.
13. No junte pilas nuevas con pilas usadas.
14. No junte pilas alcalinas con pilas regulares
(carbón-zinc) o pilas recargables (NiCd o NiMH).
INSTRUCCIONES DE
MANTENIMIENTO
MANTENIMIENTO DE
SU RECORTADORA
LUBRICACIÓN
Lubrique las cuchillas aproximadamente una
vez al mes, usando el aceite provisto. Para no
ensuciar, haga esto encima de un periódico.
Sostenga el aparato al revés y enciéndelo.
Coloque una gota de aceite sobre las cuchillas,
apague el aparato y limpie el exceso de aceite
con un paño suave.
No use demasiado aceite y no lubrique el
aparato más de lo necesario. Esto podría
dañar el motor. Tampoco no intente lubricar
las piezas del motor, las cuales son lubricadas
de por vida. Regrese el aparato y el aceite
lubricante en la base. MANTENGA EL ACEITE
FUERA DEL ALCANCE DE LOS NIÑOS.
BOTÓN DE ENCENDIDO/APAGADO
Para encender el aparato, deslice el botón de
encendido/apagado hacia las cuchillas. Para
apagarlo, deslícelo hacia atrás.
**Requiere 2 pilas AA (no incluidas). Le aconsejamos que
utilice pilas alcalinas, las cuales son más duraderas.
LIMPIEZA DE LAS CUCHILLAS
Las cuchillas de su aparato fueron diseñadas
con precisión para un uso específico, y deben
recibir un cuidado muy especial. Limpie las
cuchillas después de cada uso con el cepillo de
limpieza provisto. Guarde el aparato en la base
de almacenaje para proteger las cuchillas.
Tenga cuidado cuando sea necesario cambiar
o ajustar las cuchillas. Asegúrese de que las
dos cuchillas siempre estén cambiadas o afila-
das al mismo tiempo.
Para seguir disfrutando de su aparato durante
mucho tiempo, utilícelo únicamente con el
propósito para el cual fue diseñado: cortar la
barba y el bigote.
REMOCIÓN DE LAS CUCHILLAS
Su cortadora está equipada con cuchillas
extraíbles, para facilitar el mantenimiento, la
limpieza, y el reemplazo de las mismas.
Remoción:
• Asegúrese de que el aparato esté apagado.
• Sostenga el aparato con el interruptor
adelante y empuje las cuchillas hacia arriba
para desencajarlas.
INSTALACIÓN:
• Si observa el aparato desde arriba, verá una
hendidura en la parte posterior.
• Hay una lengüeta en la parte inferior del
juego de cuchillas.
Introduzca la lengüeta en la hendidura.
Enganche el juego de cuchillas en su lugar
hasta que calce emitiendo un chasquido.
BARBAS Y BIGOTES
El tipo de barba o de bigote que más conviene
a una persona depende de:
1. La forma y el tamaño de su rostro.
2. La forma del crecimiento natural de su
barba o de su bigote.
3. El espesor de su barba o de su bigote. Si no
está seguro del tipo de barba o bigote que le
conviene, pida consejo a un barbero. Después
de dar forma a su barba o a su bigote, deberá
mantener su aspecto, usando la cortadora una
vez por semana.
Para lograr resultados óptimos, humedezca
ligeramente su barba antes de recortarla (no la
moje). Esto evitará cortar demasiado pelo.
TIPOS DE BARBAS Y BIGOTES
CÓMO CORTAR SU BARBA
EL CONTORNEO
1. Se le hará más fácil cor-
tar la barba si está limpia y
ligeramente humedecida.
2. Peine la barba en la dirección del crecimiento
natural del pelo antes de empezar a darle forma.
3. Dé forma a su barba empezando debajo de
la quijada y subiendo hacia la oreja, en cada
lado del rostro. Siga dando forma al área de la
mejilla, a las patillas y a la línea de nacimiento
del cabello.
Compartimiento de
las pilas
Botón de encendido/apagado
EL RECORTE
1. Su cortadora incluye una guía ajustable con
5 posiciones que corta el pelo de 3 mm (1/8
pulgada) a 16 mm (5/8 pulgada).
2. Instale la guía ajustable encima de la
cuchilla para la barba. Le recomendamos
que utilice el ajuste más largo (16 mm) para
empezar. Siempre podrá volver a acortar la
barba.
3. Empiece a cortar su
barba con movimientos
parejos y suaves, desde
las patillas hasta la
quijada. Nunca corte en
dirección contraria al crecimiento natural del
pelo. El recorte resultaría demasiado corto.
4. Si desea un recorte aún más corto, escoja
un largo de recorte más corto, como 9.5 mm
(3/8 pulgada) o 12.5 mm (1/2 pulgada), y siga
acortando su barba hasta conseguir el tamaño
deseado.
IGUALAR LA QUIJADA
1. Las guías para la quijada le permitirán lograr
un recorte neto y preciso. Instale la guía encima
de la cuchilla de acabado.
2. Sostenga la cortadora recta y corte el pelo
usando pequeños movimientos uniformes.
3. Después de terminar, apague el aparato y
retire el accesorio.
CÓMO CORTAR SU BIGOTE
1. Se le hará más fácil cortar su bigote si está
limpio y ligeramente humedecido.
2. Peine su bigote en la
dirección del crecimiento
natural del pelo.
3. Instale la guía ajustable
sobre las cuchillas. Empiece con la posición más
larga (siempre podrá volver a acortar el bigote).
SIEMPRE CORTE SU BIGOTE
DESDE ARRIBA HASTA ABAJO
4. Después de terminar,
retire la guía y dé forma
a la parte inferior de su
bigote.